Skip to content

Growth of polycrystalline CVD-diamond and its defective structure

MetadataDetails
Publication Date2020-09-01
JournalIOP Conference Series Materials Science and Engineering
AuthorsA L Maslov, N. I. Polushin, А. I. Laptev, E. A. Vysotina, T. V. Martynova
InstitutionsNational University of Science and Technology
AnalysisFull AI Review Included
  • Material Focus: Synthesis and characterization of polycrystalline CVD (PCD) diamond films on silicon substrates for photonic and electronic applications.
  • Substrate Strategy: Used silicon wafers (25 mm diameter, 2.5-3.0 mm thickness) with sub-1 nm surface roughness, pre-treated with detonation nanodiamonds (DNA-STP, 4-6 nm particle size) to seed nucleation.
  • Optimal Process Window: Microwave power 4.0-4.2 kW, chamber pressure 75 torr (10 kPa), substrate temperature ~1000 °C, with a two-stage gas flow ramp (high-CH4 startup followed by steady-state flow).
  • Growth Rate: Approximately 2 µm/h during steady-state operation, reaching a total film thickness of 500 µm over ~30 hours of deposition.
  • Defect Identification: Small peripheral cracks caused by thermal stress mismatch during cooling; the central region exhibits a uniform, defect-free polycrystalline topography.
  • Core Outcome: Establishment of a reproducible recipe for crack-minimized, large-area PCD films, enabling scalable wafer diameters for downstream device fabrication.
  • Implied Application: Free-standing PCD plates and electrodes for use in electrochemical cells, heat spreaders, and radiation-hard electronics.
ParameterValueUnitContext
Substrate MaterialSilicon (Si)—Pre-polished, modified with nanodiamond seeds
Substrate Diameter25mmStandard wafer size used in this study
Substrate Thickness2.5 - 3.0mmMechanical support during CVD growth
Substrate Surface Roughness< 1nmPre-deposition polishing requirement
Nanodiamond Seed Size4 - 6nmDNA-STP detonation nanodiamond powder
Seeding Mass0.002gLoaded into UNIS VKV reactor
Carrier SolventEthyl alcohol (0.1 L)—Colloidal suspension medium
Ultrasonic Treatment Power500WSeeding dispersion parameters
Ultrasonic Treatment Time4minSeeding dispersion parameters
Microwave Power4.0 - 4.2kWArdis 300 system
Chamber Pressure75 (10 kPa)torrTotal gas pressure during growth
Substrate Temperature~1000 - 1100°COptimal process window
CH4 Purity99.5%Feed gas
H2 Purity99.9995%Feed gas
Steady-State H2 Flow591cm3/minReference parameters
Steady-State CH4 Flow9cm3/minReference parameters
Stage 1 H2 Flow580cm3/minFirst 3-5 hours
Stage 1 CH4 Flow20cm3/minHigh-methane nucleation stage
Steady-State Growth Rate~2µm/hAfter initial nucleation
Total Film Thickness500µmFinal deposited thickness
Total Deposition Time~30hTo reach 500 µm
Primary DefectPeripheral microcracks—Thermal stress at wafer edge
  • Substrate Preparation: Silicon wafers polished to Ra < 1 nm, then chemically treated with reagents to convert the surface from hydrophobic to hydrophilic for uniform wetting.
  • Colloidal Seeding: 0.002 g of nanodiamond powder dispersed in 0.1 L ethyl alcohol via ultrasonic cavitation (500 W, 4 min) in a UNIS VKV reactor.
  • Seeding Application: Colloidal suspension applied to the substrate and mechanically rubbed with a lint-free cloth to embed nucleation centers.
  • Reactor Platform: Ardis 300 MPCVD system operated at 4.0-4.2 kW microwave power.
  • Two-Stage Gas Recipe:
    • Stage 1 (Nucleation, 3-5 h): H2 at 580 cm3/min, CH4 at 20 cm3/min (~4% CH4).
    • Stage 2 (Steady-State Growth): H2 at 591 cm3/min, CH4 at 9 cm3/min (~1.5% CH4).
  • Process Parameters: Chamber pressure maintained at 75 torr (10 kPa); substrate surface temperature held at ~1000 °C.
  • Film Characterization: Surface topography evaluated via optical microscopy; crystal structure confirmed by selected-area electron diffraction (SAED) on a JEM JEOL 2100 TEM.
  • Defect Mapping: Peripheral crack zones and central crack-free zones separately imaged to correlate thermal stress with microstructure.

The polycrystalline diamond films described in this paper map directly to 6CCVD’s Optical Grade PCD and Free-Standing PCD Wafer product lines. For replication of the reported 500 µm-thick, 25 mm-diameter films, our standard polycrystalline diamond plates are an ideal starting point. For researchers extending this work to larger-area or thicker films, 6CCVD routinely produces PCD plates up to 125 mm in diameter and substrates up to 10 mm in thickness, eliminating the wafer-edge thermal-stress pathways that drove the cracking observed in the reference study.

The paper’s emphasis on matched deposition windows and crack mitigation is precisely where 6CCVD’s custom fabrication services add value. We offer:

  • Custom Metalization: Ti, Pt, Au, Pd, W, and Cu films applied via in-house sputtering/evaporation—directly relevant if the downstream goal is PCD electrodes for electrochemical or sensor applications.
  • Laser Cutting & Dicing: Free-standing PCD wafers can be cut to user-defined geometries, removing the “waste” cost penalty the authors cite as a motivation for large-area films.
  • Surface Finishing: Post-growth polishing to Ra < 5 nm on inch-size PCD, enabling optical and tribological follow-up studies.
  • Thickness Grading: Films from 0.1 µm up to 500 µm-and-beyond, with substrates up to 10 mm for thermal management or heat-spreader use cases.

6CCVD’s in-house PhD engineering team routinely supports researchers working on thermal-stress modeling, defect-density reduction, and scale-up of MPCVD processes. If you are transitioning from a 25 mm Si-supported film to a 100 mm or 125 mm free-standing PCD plate, or shifting the application from fundamental growth studies to electrochemical electrodes, photonics, or radiation-hard electronics, our team can assist with material selection, seeding strategies, and metal stack design.

For custom specifications, metalization stack consultation, or material selection for your next polycrystalline diamond deposition campaign, visit 6ccvd.com or contact our engineering team directly.

View Original Abstract

Abstract Polycrystalline diamond films are used in various fields of science and technology, for example, in photonics and electronics. The growth of high-quality polycrystalline films is restrained by the formation of small cracks at the periphery, which are associated with thermal stresses, as well as a low growth rate. Treatment of the substrate surface makes it possible to increase the initial rate of film formation and to form a continuous layer of diamond film on its surface. In this work, we presented the results of the synthesis of polycrystalline films, the optimal deposition mode and the growth rate of such the film and the topology of its surface. The results obtained in the future will make it possible to obtain high-quality polycrystalline diamond films of a larger area, which will significantly increase the diameter of finished products made of them.